WindowsXPのインストール

AptivaのBIOS設定画面

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

一番最初の画面　（スタート時、F1キーで表示）

	configuration /Setup Utility
	Select Option
�T	・	System Summary
�U	・	Product Data
�V	・	Devices and I/OPorts		→２．IDE-HDの切り離しへ
�W	・	Start Options		→１．Boot装置の順序へ
�X	・	Data and Time
�Y	・	Advanced Setup
�Z	・	PowerManagement Setup
�[	・	Clock Generator Control
		Loud Default Settings
		Set Passward
		Save & Exit Setup
		Exit Without Saving

１．Boot装置の順序

		�W Start Options
1	・	Startup Sequence		→次の画面へ
2		VirusWarning	[Disabled]
3		CPU LZ Cache ECC Cheking	[Enabled]
4		Processor Number Feature	[Enabled]
5		Quick Power On Self Test	[Enabled]
6		Boot Up Floppy Seek	[Enabled]
7		Boot Up NumLock Status	[On]
8		Gate A20 Option	[Fast]
9		TypematicRate Setting	[Disabled]
10		Typematic Rate (Chars/Sec)	6
11	x	Typematic Delay (Msec)	250
12		Report No FDD for WIN 95
13		Halt On	[All Errors]

１． Startup Sequence (1) First Boot Device [Floppy] →Floppy (2) Second Boot Device [HDD-0] →CDROM (3) Third Boot Device [SCSI] →SCSI (4) Boot Other [Enabled] →Enabled	→	１． 選べる種類 1) Floppy 　 9) LAN 2) LS/ZIP 　 10) Disabled 3) HDD-0 　 11) Enabled 4) SCSI 　 5) CDROM 　 6) HDD-1 　 7) HDD-2 　 8) HDD-3

　

２．IDEハードディスクの切り離し

一番最初の画面（再掲）

	Configuration /Setup Utility
	Select Option
�T	・	System Summary
�U	・	Product Data
�V	・	Devices and I/OPorts		→２．IDE-HDの切り離しへ
�W	・	Start Options		→１．Boot装置の順序へ
�X	・	Data and Time
�Y	・	Advanced Setup
�Z	・	PowerManagement Setup
�[	・	Clock Generator Control
		Loud Default Settings
		Set Passward
		Save & Exit Setup
		Exit Without Saving

	�V Devices and I/O Ports
1		Disketle DriveA	[1.44M,3.5in.]
2		PS/2 mousefunction		[Enable]
3		On Bord AUDIO		[Enable]
4		On Bord Lan		[Enable]
5	・	Serial Port Setup ．．．
6	・	parallel Port Setup ．．．
7	・	USB Setup ．．．
8	・	IDE Drives Setup ．．．		→次の画面へ
9	・	Video Setup ．．．
10		PS2 MouseDetectFunction		[Enable]
11		Onboad FDC Controller		[Enable]
12		Game Port Address		[201]
13		Midi Port Address		[330]
14		Midi Port IRQ		[10]

�V-8	IDEDrive Setupの設定項目
(1)	Internal PCI/IDE	Both	→	Secondary
(2)	IDE Primary Master PIO	[Auto]
(3)	IDE Primary Slave PIO	[Auto]
(4)	IDE Secondary Master PIO	[Auto]
(5)	IDE Secondary Slave PIO	[Auto]
(6)	Primary Master UltraDMA	[Auto]
(7)	Primary Slave UltraDMA	[Auto]
(8)	Secondary Master UltraDMA	[Auto]
(9)	Secondary Slave UltraDMA	[Auto]
(10)	IDE Burst Mode	[Enabled]
(11)	IDE Data Port Post Write	[Disabled]
(12)	IDE HDD Block Mode	[Enable]

---

［前の場所に戻る］ ［親ページへ戻る］